Search results

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 350-450 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T8, T10, T12 or 4-Pin Long Compact

Category: Emergency Fluorescent Ballasts

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following Lamp Types: (1) Philips LED T8 InstantFit, BiPin, 8.5 - 16.5W. (designated by new Silver Can)

Category: Emergency Fluorescent Ballasts

LED Emergency Driver - Input Voltage: 120-277V AC. Operates an LED Load of up to 10W at nominal battery voltage for a minimum of 90 minutes. UL RECOGNIZED Factory Installation * (Indoor and Damp) Output Class 2 Compliant **BSL310 is field installable when used with the Philips EvoKit LED Retrofit Luminaire and installed by Licensed Electrician** See pg. 6 of Wiring Diagram .pdf **

Category: LED Driver Emergency Power Supplies

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 600-1325 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T5, T8, T10, T12, 4-Pin (2G11) or (1) Philips InstantFit LED T8 4' lamp ***Discontinued, See Sub***

Category: Emergency Fluorescent Ballasts

Emergency Ballast, Fluorescent, 2 Lamp, 300-700 Lumens, 120-277 Volt, 90 Minute Illumination Time

Category: Emergency Fluorescent Ballasts

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. The B94CGU can be used with one 13 - 42 W (4-pin) twin, quad or triple twin-tube compact. It is also compatible with most one-, two-, three- and four-lamp electronic, standard, energy-saving and dimming AC ballasts

Category: Emergency Fluorescent Ballasts

LED Emergency Driver. Input Voltage: 120/277 Volts AC, 60Hz. Output Voltage: 120/277 VAC, 60Hz. Maximum Load Power (including AC ballast/driver): 100 Watts. SINE WAVE Emergency Lighting inverter with Dimming Capabilities

Category: LED Driver Emergency Power Supplies

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 500-600 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T8, T10, T12 or 4-Pin Long Compact.

Category: Emergency Fluorescent Ballasts

Emergency LED Driver: Metal case, dual conduit on one end with lead wires in each conduit, and separate 2-wire ITS switch kit with wall plate. Universal Input Voltage: 120-277 VAC, 50/60 Hz, Output Voltage: 15-50 VDC, Output Power: 10.4 W (Maximum). Weight: 3.45 lbs.(1.57kg), Dimensions: 15.34” x 2.25” x 1.16” (mounting center - 15.0”). Compatible with AC drivers and LED loads rated for Class 2. Order no. BSL310CDFT1M, 12NC: 913702457201

Category: LED Driver Emergency Power Supplies

10 Watt Emergency Driver for Linear LED Strips, 120-277 Volt, 90 Minute Illumination Time

Category: LED Driver Emergency Power Supplies

LED Emergency Driver - Input Voltage: 120-277V AC. Matal Case with Conduit. Operates an LED Load of up to 10W at nominal battery voltage for a minimum of 90 minutes. Listed to UL924 and tested to CSA 22.2, No. 141 For Field or Factory Installation (Indoor and Damp) Output Class 2 Compliant **BSL310 is field installable when used with the Philips EvoKit LED Retrofit Luminaire and installed by Licensed Electrician** See pg. 6 of Wiring Diagram .pdf **

Category: LED Driver Emergency Power Supplies

10 Watt Emergency LED Driver, Class 2 Output, Very Compact Low Profile Case, ABConnect and STSelect Equipped, Metal IP65 Bi-Color LED and Test Switch, 14.1” x 1.18” x 1"

Category: LED Driver Emergency Power Supplies

Emergency LED Driver, 120-277 Volt AC Input, 15-50 Volt DC Output, 7.5 Watts Output Power

Category: LED Driver Emergency Power Supplies

LED Emergency Driver, 6 Watt, 120-277 Volt Input, 15-54 Volt DC Output

Category: LED Driver Emergency Power Supplies

10 Watt Emergency Driver for Linear LED Strips, 120-277 Volt, 90 Minute Illumination Time, Metal Case No Conduit

Category: LED Driver Emergency Power Supplies

Emergency ballast for Fluorescent and Type A TLED lamps. Input Voltage: 120/277V, 90 Minute Illumination Time up to 1400 lumens, 24 Hr Recharge. For use with the following Compact, Linear, U-Bent & Circline Fluorescent Lamp Types: (1-2) 17 - 40W, 2’ - 4’, T8, T9, T10 or T12 fluorescent lamps, (1) 4-pin, 2G11, 18 - 55W long compacts, (1) 4-pin, G24q/Gx24q, 13 - 42W CFL, (1) T5/T5HO, BiPin or Circline, 14 - 55W, (1) 4-pin, GR10q, 16 - 55W 2D and Compatible with 7 - 16.5W Type A TLED lamps (including LED T8 InstantFit). Meets CEC Title 20 efficiency standards. Includes 2W-ITS (2-wire Illuminated Test Switch).

Category: Emergency Fluorescent Ballasts